Netgear: Overview

XB1R Hades · Apr 27, 2014

Netgear (Routers): Overview
Netgear JNR3210

Login Information

Gateway - 192.168.1.1, 10.0.0.1, or http://routerlogin.net

Username - admin

Password - password

Netgear Smart Wizard - Light Blue

How to Find SSID (Network Name)

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

The Network name will be listed as Name (SSID).

How To Find Wireless Passphrase (WPA/WEP)

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

The wireless passphrase can be found near the bottom of the page.

Changing Wireless Security Type/ Disabling Wireless Security

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

Under Security Options select Disable.

Select Apply

Change Wireless Channel

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).

Click Apply.

Change Wireless Mode

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

Select from the mode drop down "Up to 54Mbps".

Click Apply.

Change Wireless Band (Width)

The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set
the wireless band to 20MHz only, follow these steps.

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering Router login in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

Select from the mode drop down "Up to 217Mbps" or lower.

Select Apply.

MAC Filtering

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

Under advanced select Wireless Settings.

Select Setup Access List To access MAC Filtering.

Uncheck Turn Access Control On

Select Apply.

DHCP Reservation

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin"/password.

Click LAN Setup on the left.

At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.

In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then
click "Add" to finish the process.

UPnP

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left under the advanced section choose UPnP.

Toggle UPnP.

DMZ

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left under the advanced section select WAN Setup.

Check the box next to Default DMZ Server.

Enter the IP address assigned to the Xbox console you wish to DMZ.

Disable DMZ

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left under the advanced section select WAN Setup.

Uncheck the box next to Default DMZ Server.

Select apply.

Port Forwarding

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Click the Add Custom Service button at the bottom.

In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish
to port forward has.

Click Apply.

Disable Port Forwarding

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Select the radio button for any rules needed to be removed.

Select Delete Service.

Select apply.

Firewall

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the menu on the left select WAN Setup.

Check the Disable SPI Firewall box.

Change NAT filtering from secured to Open.

How to Find Firmware Version

Plug the computer into a LAN port via an Ethernet cable.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the left hand menu select Router Status.

The firmware version will be listed as Firmware Version.

Firmware Update

Auto Update

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

The Netgear smart wizard will automatically search for updates upon login, if an update is available click install.

Manual Update

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Administraion from the menu on the left.

Select Router Update from the submenu.

In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, un-compress the file.

Click Browse.

Locate and select the file you just downloaded and uncompressed.

Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router
finishes restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.

Click Router Status and check the Firmware Version to verify that your router now has the new software installed

Restore Factory Defaults

Through firmware

Plug the computer into a LAN port via an Ethernet cable.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the left hand menu select Backup Settings.

Select the Erase option under where it says Revert to factory default settings.

Through Hardware

*There is no physical reset button on this device as far as we can tell. Please consult your user manual or Netgear support for information on how to perform a factory reset via the hardware.

Entering PPPoE

Plug the computer into a LAN port via an Ethernet cable.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".

From the left hand menu select Basic Settings.

Where it says Does your internet connection require a login select yes.

Enter the user name and password for your PPPoE in their respective fields.

Select apply.

Netgear Genie - Black/Purple

How to Find SSID (Network Name)

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

The default user name and password are: "admin", "password".

Select Basic from the menu on the top.

Select Wireless from the left menu.

Your network name will be listed as Name(SSID).

How To Find Wireless Passphrase (WPA/WEP)

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

From the menu on the left under the Setup section choose Wireless Settings

The wireless passphrase can be found near the bottom of the page.

Changing Wireless Security Type/ Disabling Wireless Security

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

From the menu on the left under the Setup section choose Wireless Settings

Under Security Options select the desired security type.

Select Apply.

MAC Filtering

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Advanced from the menu on the left.

Under Advanced select Wireless Settings.

Select Setup Access List To access MAC Filtering.

Uncheck Turn Access Control On

Select Apply.

Change Wireless Channel

Plug the computer into a LAN port via an Ethernet cable.

Open a web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select Wireless settings from the left hand menu under Setup.

From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11)

Click Apply.

Change Wireless Mode

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select from the mode drop down "Up to 54Mbps".

Click Apply.

Change Wireless Band (Width)

The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set
the wireless band to 20MHz only, follow these steps.

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering Router login in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select from the mode drop down "Up to 217Mbps" or lower.

Select Apply.

DHCP Reservation

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin"/password.

Select Advanced from the tabs at the top.

Click Setup from the menu on the left.

Click Lan Setup in the submenu that appears.

At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.

In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then
click "Add" to finish the process.

UPnP

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu choose UPnP.

Toggle UPnP.

DMZ

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Setup.

Select WAN Setup from the submenu.

Check the box next to Default DMZ Server if it is not.

Enter the IP address assigned to the Xbox console you wish to DMZ

Select Apply.

Disable DMZ

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Setup.

Select WAN Setup from the submenu.

Uncheck the Default DMZ Server

Select Apply.

Port Forwarding

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Click the Add Custom Service button at the bottom.

In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish
to port forward has.

Click apply.

Disable Port Forwarding

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Select the service you want to delete from the radio button on the left.

Select Delete Service.

Firewall

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Setup from the menu on the left.

From the submenu select WAN Setup.

Check the Disable SPI Firewall box.

Change NAT Filtering from secured to Open.

Restore Factory Defaults

Through firmware

Plug the computer into a LAN port via an Ethernet cable.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Administration from menu on the left.

From the submenu select Backup Settings.

Select the Erase option under where it says Revert to factory default settings.

Through Hardware

*There is no physical reset button on this device as far as we can tell. Please consult your user manual or Netgear support for information on how to perform a factory reset via the hardware.

How to Find Firmware Version

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Administration from the menu on the left.

Select Router Status under administration.

The Firmware version will be listed as Firmware Version.

Firmware Update

Auto Update

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

The Netgear smart wizard will automatically search for updates upon login, if an update is available click install.

Manual Update

Plug the computer into a LAN port via an Ethernet cable.

Open web browser.

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select administration from the menu on the left.

Select Router Update from the submenu.

In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, un-compress the file.

Click Browse.

Locate and select the file you just downloaded and uncompressed.

Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router
finishes restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.

Click Router Status and check the Firmware Version to verify that your router now has the new software installed.

Entering PPPoE

Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select the Basic tab from the tabs at the top.

Select Internet from the menu on the left

Where it asks if your internet connection requires a login select yes.

Input in your PPPOE user name and password.

Select Apply.

Known Issues

There are no known issues with this device.

Multiple Console Support

We have no confirmed cases where multiple consoles were able to obtain an Open NAT state while using this device. Please comment on this page if you have been able obtain Open NAT on two or more consoles using this device.

:)

XB1R Apollo · Apr 27, 2014

Netgear: Overview

Netgear (Routers): Overview
Netgear WNDR3700

Login Information

Gateway - 192.168.1.1, 10.0.0.1, or
http://routerlogin.net

Username - admin

Password - password

Netgear Smart Wizard - Light Blue

How to Find SSID (Network Name)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

The Network name will be listed as Name (SSID).

How To Find Wireless Passphrase (WPA/WEP)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

The wireless passphrase can be found near the bottom of the page.

Changing Wireless Security Type/ Disabling Wireless Security

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

Under Security Options select Disable.

Select Apply

MAC Filtering

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

Under advanced select Wireless Settings.

Select Setup Access List To access MAC Filtering.

Uncheck Turn Access Control On

Select Apply.

Change Wireless Channel

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).

Click Apply.

Change Wireless Mode

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

Select from the mode drop down "Up to 54Mbps".

Click Apply.

Change Wireless Band (Width)

The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set the wireless
band to 20MHz only, follow these steps.

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering Router login in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

Select from the mode drop down "Up to 130Mbps" or lower.

Select Apply.

DHCP Reservation

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin"/password.

Click LAN Setup on the left.

At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.

In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
"Add" to finished the process.

UPnP

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the advanced section choose UPnP.

Toggle UPnP.

DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".

From the menu on the left under the advanced section select WAN Setup.

Check the box next to Default DMZ Server.

Enter the IP address assigned to the Xbox console you wish to DMZ.

Disable DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".

From the menu on the left under the advanced section select WAN Setup.

Uncheck the box next to Default DMZ Server.

Select apply.

Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Click the Add Custom Service button at the bottom.

In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
port forward has.

Click Apply.

Disable Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Select the radio button for any rules needed to be removed.

Select Delete Service.

Select apply.

Firewall

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left select WAN Setup.

Check the Disable SPI Firewall box.

Change NAT Filtering from secured to Open.

How to Find Firmware Version

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the left hand menu select Router Status.

The firmware version will be listed as Firmware Version.

Firmware Update

Auto Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

The netgear smart wizard will automatically search for updates upon login, if an update is available click install.

Manual Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Administraion from the menu on the left.

Select Router Update from the submenu.

In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.

Click Browse.

Locate and select the file you just downloaded and uncompressed.

Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.

Click Router Status and check the Firmware Version to verify that your router now has the new software installed

Restore Factory Defaults

Through firmware

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the left hand menu select Backup Settings.

Select the Erase option under where it says Revert to factory default settings.

Through Hardware

Plug the computer into a LAN port via an ethernet cable.

Locate the reset button on the device.

With paperclip/pen/toothpick hold down the reset button down for 30 seconds.

Wait for lights to turn off then return to normal.

Entering PPPoE

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the left hand menu select Basic Settings.

Where it says Does your internet connection require a login select yes.

Enter the user name and password for your pppoe in their respective fields.

Select apply.

Netgear Genie - Black/Purple

How to Find SSID (Network Name)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the menu on the top.

Select Wireless from the left menu.

Your network name will be listed as Name(SSID).

How To Find Wireless Passphrase (WPA/WEP)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

From the menu on the left under the Setup section choose Wireless Settings

The wireless passphrase can be found near the bottom of the page.

Changing Wireless Security Type/ Disabling Wireless Security

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

From the menu on the left under the Setup section choose Wireless Settings

Under Security Options select the desired security type.

Select Apply.

MAC Filtering

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the menu on the left.

Under Advanced select Wireless Settings.

Select Setup Access List To access MAC Filtering.

Uncheck Turn Access Control On

Select Apply.

Change Wireless Channel

Plug the computer into a LAN port via an ethernet cable.

Open a web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select Wireless settings from the left hand menu under Setup.

From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11)

Click Apply.

Change Wireless Mode

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select from the mode drop down "Up to 54Mbps".

Click Apply.

Change Wireless Band (Width)

The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set the wireless
band to 20MHz only, follow these steps.

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering Router login in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select from the mode drop down "Up to 130Mbps" or lower.

Select Apply.

DHCP Reservation

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin"/password.

Select Advanced from the tabs at the top.

Click Setup from the menu on the left.

Click Lan Setup in the submenu that appears.

At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.

In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
"Add" to finished the process.

UPnP

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu choose UPnP.

Toggle UPnP.

DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Setup.

Select WAN Setup from the submenu.

Check the box next to Defualt DMZ Server if it is not.

Enter the IP address assigned to the Xbox console you wish to DMZ

Select Apply.

Disable DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Setup.

Select WAN Setup from the submenu.

Uncheck the Default DMZ Server

Select Apply.

Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Click the Add Custom Service button at the bottom.

In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
port forward has.

Click apply.

Disable Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Select the service you want to delete from the radio button on the left.

Select Delete Service.

Firewall

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Setup setup from the menu on the left.

From the submenu select WAN Setup.

Check the Disable SPI Firewall box.

Change NAT Filtering from secured to Open.

How to Find Firmware Version

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Administration from the menu on the left.

Select Router Status under administration.

The Firmware version will be listed as Firmware Version.

Firmware Update

Auto Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

The netgear smart wizard will automatically search for updates upon login, if an update is available click install.

Manual Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select administration from the menu on the left.

Select Router Update from the submenu.

In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.

Click Browse.

Locate and select the file you just downloaded and uncompressed.

Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.

Click Router Status and check the Firmware Version to verify that your router now has the new software installed.

Restore Factory Defaults

Through firmware

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Administration from menu on the left.

From the submenu select Backup Settings.

Select the Erase option under where it says Revert to factory default settings.

Through Hardware

Plug the computer into a LAN port via an ethernet cable.

Locate the reset button on the device.

With paperclip/pen/toothpick hold down the reset button down for 30 seconds.

Wait for lights to turn off then return to normal.

Entering PPPoE

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Basic tab from the tabs at the top.

Select Internet from the the menu on the left

Where it asks if your internet connection requires a login select yes.

Input in your PPPOE user name and password.

Select Apply.

Device Manual

WNDR3700v1

WNDR3700v2

WNDR3700v3

WNDR3700v4

Known Issues

This device has no known issues.

Multiple Console Support

We have confirmed cases where this devices is able to support two or more consoles with Open NAT on this device.

XB1R Athena · Apr 27, 2014

Netgear: Overview

Netgear (Routers): Overview
Netgear WNR3500

Login Information

Gateway - 192.168.1.1, 10.0.0.1, or routerlogin.net

Username - admin

Password – password

Netgear Smart Wizard - Light Blue

How to Find SSID (Network Name)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

The Network name will be listed as Name (SSID).

How To Find Wireless Passphrase (WPA/WEP)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

The wireless passphrase can be found near the bottom of the page.

Changing Wireless Security Type/ Disabling Wireless Security

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the Setup section choose Wireless Settings.

Under Security Options select Disable.

Select Apply

MAC Filtering

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

Under advanced select Wireless Settings.

Select Setup Access List To access MAC Filtering.

Uncheck Turn Access Control On

Select Apply.

Change Wireless Channel

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).

Click Apply.

Change Wireless Mode

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".

Select Wireless settings from the left hand menu under Setup.

Select from the mode drop down "Up to 54Mbps".

Click Apply.

Change Wireless Band (Width)

This router only supports the 20MHz band.

DHCP Reservation

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin"/password.

Click LAN Setup on the left.

At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.

In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
"Add" to finished the process.

UPnP

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left under the advanced section choose UPnP.

Toggle UPnP.

DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".

From the menu on the left under the advanced section select WAN Setup.

Check the box next to Default DMZ Server.

Enter the IP address assigned to the Xbox console you wish to DMZ.

Disable DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".

From the menu on the left under the advanced section select WAN Setup.

Uncheck the box next to Default DMZ Server.

Select apply.

Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Click the Add Custom Service button at the bottom.

In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
port forward has.

Click Apply.

Disable Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Select the radio button for any rules needed to be removed.

Select Delete Service.

Select apply.

Firewall

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the menu on the left select WAN Setup.

Check the Disable SPI Firewall box.

Change NAT Filtering from secured to Open.

How to Find Firmware Version

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Administration from the menu on the left.

Select Router Status under administration.

The Firmware version will be listed as Firmware Version.

Firmware Update

Auto Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

The netgear smart wizard will automatically search for updates upon login, if an update is available click install.

Manual Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Administraion from the menu on the left.

Select Router Update from the submenu.

In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.

Click Browse.

Locate and select the file you just downloaded and uncompressed.

Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.

Click Router Status and check the Firmware Version to verify that your router now has the new software installed

Restore Factory Defaults

Through firmware

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the left hand menu select Backup Settings.

Select the Erase option under where it says Revert to factory default settings.

Through Hardware

Plug the computer into a LAN port via an ethernet cable.

Locate the reset button on the device.

With paperclip/pen/toothpick hold down the reset button down for 30 seconds.

Wait for lights to turn off then return to normal.

Entering PPPoE

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the left hand menu select Basic Settings.

Where it says Does your internet connection require a login select yes.

Enter the user name and password for your pppoe in their respective fields.

Select apply.

Netgear Genie - Black/Purple

How to Find SSID (Network Name)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the menu on the top.

Select Wireless from the left menu.

Your network name will be listed as Name(SSID).

How To Find Wireless Passphrase (WPA/WEP)

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

From the menu on the left under the Setup section choose Wireless Settings

The wireless passphrase can be found near the bottom of the page.

Changing Wireless Security Type/ Disabling Wireless Security

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

From the menu on the left under the Setup section choose Wireless Settings

Under Security Options select the desired security type.

Select Apply.

MAC Filtering

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the menu on the left.

Under Advanced select Wireless Settings.

Select Setup Access List To access MAC Filtering.

Uncheck Turn Access Control On

Select Apply.

Change Wireless Channel

Plug the computer into a LAN port via an ethernet cable.

Open a web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select Wireless settings from the left hand menu under Setup.

From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11)

Click Apply.

Change Wireless Mode

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Basic from the tabs at the top.

Select Wireless from the left hand menu.

Select from the mode drop down "Up to 54Mbps".

Click Apply.

DHCP Reservation

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin"/password.

Select Advanced from the tabs at the top.

Click Setup from the menu on the left.

Click Lan Setup in the submenu that appears.

At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.

In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
"Add" to finished the process.

UPnP

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu choose UPnP.

Toggle UPnP.

DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Setup.

Select WAN Setup from the submenu.

Check the box next to Default DMZ Server if it is not.

Enter the IP address assigned to the Xbox console you wish to DMZ

Select Apply.

Disable DMZ

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select Setup.

Select WAN Setup from the submenu.

Uncheck the Default DMZ Server

Select Apply.

Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Click the Add Custom Service button at the bottom.

In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
port forward has.

Click apply.

Disable Port Forwarding

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Advanced setup from the menu on the left.

From the submenu select Port Forwarding/Port Triggering.

Select the Port Forwarding button at the top of the main screen.

Select the service you want to delete from the radio button on the left.

Select Delete Service.

Firewall

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Setup setup from the menu on the left.

From the submenu select WAN Setup.

Check the Disable SPI Firewall box.

Change NAT Filtering from secured to Open.

How to Find Firmware Version

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".

From the left hand menu select Router Status.

The firmware version will be listed as Firmware Version.

Firmware Update

Auto Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

The netgear smart wizard will automatically search for updates upon login, if an update is available click install.

Manual Update

Plug the computer into a LAN port via an ethernet cable.

Open web browser.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select Advanced from the tabs at the top.

Select administration from the menu on the left.

Select Router Update from the submenu.

In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.

Click Browse.

Locate and select the file you just downloaded and uncompressed.

Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.

Click Router Status and check the Firmware Version to verify that your router now has the new software installed.

Restore Factory Defaults

Through firmware

Plug the computer into a LAN port via an ethernet cable.

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Advanced tab from the tabs at the top.

Select Administration from menu on the left.

From the submenu select Backup Settings.

Select the Erase option under where it says Revert to factory default settings.

Through Hardware

Plug the computer into a LAN port via an ethernet cable.

Locate the reset button on the device.

With paperclip/pen/toothpick hold down the reset button down for 30 seconds.

Wait for lights to turn off then return to normal.

Entering PPPoE

Login to router by entering
http://routerlogin.net in to the address bar or by entering the default gateway IP address.

The router will then prompt you to enter the username and password.

the default user name and password are: "admin", "password".

Select the Basic tab from the tabs at the top.

Select Internet from the the menu on the left

Where it asks if your internet connection requires a login select yes.

Input in your PPPOE user name and password.

Select Apply.

Multiple Console Support

We have confirmed that this network device is unable to support more than one console with an Open NAT.

Device Manual

WNR3500

WNR3500v2

Known Issues

There are no known issues with this device.

DannyTx

I can't seem to get my nat type to open even after all these steps and the steps xbox provides for "cant find teredo IP" when i run multiplayer test I get that, and when i check more details it says im behind a firewall or not connected. I made sure i disabled
SIP ALG and changed nat to open, and still doesnt work.

Mister Ohnaka

Hello Jr,

Sorry to hear about the connection troubles. Let's see if we can get this working for you.

Are you able to connect directly to your modem via an ethernet cable? This will help us narrow it down. Also, here is an overview of your router if needed for further troubleshooting: Netgear
WNR3500.

Let us know how that direct connection works, and we can go from there.

mermaidbythesea-A337

[quote user="XB1R Athena"]

Internet service type: 3G/4G

Common devices:

Sierra Wireless: Overdrive Pro

Sierra Aircard: 250U

ISP Website: http://sprint.com

Support number: 1-888-211-4727

[/quote]

JackCrilly

My model name is different from the ones listed

cookieater821

BRIDGE mode is under LAN setting routed with NAT and routed without NAT or select BRDIGE MODE. Don't forget to click APPLY then power cycle gateway -

Netgear: Overview