Zyxel Zyxel C1000z: Overview

Discus and support Zyxel Zyxel C1000z: Overview in XboX Networking Hardware to solve the problem; Zyxel (Modems/Gateways) Zyxel C1000z: Overview Login Information Gateway: 192.168.0.1 Username: admin Password: (located on the bottom of the... Discussion in 'XboX Networking Hardware' started by XB1R Hydros, Jun 27, 2014.

  1. XB1R Hydros
    XB1R Hydros Guest

    Zyxel Zyxel C1000z: Overview


    Zyxel (Modems/Gateways) Zyxel C1000z: Overview
    Login Information



    • Gateway: 192.168.0.1
    • Username: admin
    • Password: (located on the bottom of the device)


    How to Find SSID (Network Name)

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Wireless Setup on the main page.
    6. On the left hand side select SSID Setup.
    7. Your current SSID will be shown on this page. You can also change the SSID from here as well.


    How To Find Wireless Passphrase (WPA/WEP)

    From Hardware:

    1. On the bottom of the device, locate the sticker with login information on it.
    2. The default wireless password will be found on the sticker.
    From Firmware:

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Wireless Setup on the main page.
    6. On the left hand side select Wireless Security.
    7. Under step 4 the default security key/passphrase will be shown here.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Wireless Setup on the main page.
    6. On the left hand side select Wireless Security.
    7. On the main page under “select security type” select the desired security type.
    8. Next select the encryption type.
    9. Type in a passphrase in the Security Key/Passphrase box.
    10. Select the Apply button to save changes.


    MAC Filtering

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Wireless Setup on the main page.
    6. On the left hand side select MAC Authentication.
    7. In the “SSID” drop down select the desired Wireless network name to enable MAC filtering.
    8. Alternatively you can select ALL SSID’s to enable MAC filtering on all wireless networks from this device.
    9. Next to “MAC Authentication” select Enable.
    10. Select Allow Device List.
    11. Select the device you would like to add next to “Select Device Name”. Or manually enter in the MAC address.
    12. Select the Apply button to save changes.


    Disable MAC Filtering

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).


    Change Wireless Channel

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Wireless Setup on the main page.
    6. On the left hand side select Radio Setup.
    7. Under the Channel dropdown, select the desired channel.
    8. Select the Apply button to save changes.


    Change Wireless Mode

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Wireless Setup on the main page.
    6. On the left hand side select Radio Setup.
    7. Under the 802.11 Mode, select the desired mode.
    8. Select the Apply button to save changes.


    Change Wireless Band (Width)

    The wireless band width cannot be changed.



    DHCP Reservation

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Advanced Setup on the main page.
    5. On the left hand side select DHCP Reservation.
    6. Under the Select MAC Address, select the desired MAC address OR manually type in the MAC address of the device you want to use.
    7. Select the IP address you would like to reserve.
    8. Select the Apply button to save changes.
    9. Verify the saved changes by checking the DHCP Reservation list. The device you added should be listed.


    UPnP

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Advanced Setup on the main page.
    5. On the left hand side select UPnP under the “Security Section”.
    6. Select the Enable option next to “UPnP”.
    7. Select the Enable option next to “UPnP NAT-T”.
    8. Select Apply once you have finished to save changes.


    DMZ

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Advanced Setup on the main page.
    5. On the left hand side select DMZ Hosting under the “Security Section”.
    6. Select the Enable option next to “DMZ”.
    7. Select the device’s IP address in the dropdown next to “Select Device”. Alternatively you can
      manually enter in the IP address for the device.
    8. Select Apply once you have finished to save changes.


    Disable DMZ

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Advanced Setup on the main page.
    5. On the left hand side select DMZ Hosting under the “Security Section”.
    6. Select the Disable option next to “DMZ”.
    7. Select Apply once you have finished to save changes.


    Port Forwarding

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Advanced Setup on the main page.
    5. On the left hand side select Port Forwarding under the “Security Section”.
    6. Select the device’s IP address in the dropdown next to “Select Device”. Alternatively you can
      manually enter in the IP address for the device.
    7. Type in the Starting Port.
    8. Type in the Ending Port.
    9. Select Both in the “Protocol” drop down.
    10. Select All IP Addresses for the “Remote Port and IP”.
    11. Select Apply to save the changes.


    Disable Port Forwarding

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Advanced Setup on the main page.
    5. On the left hand side select Port Forwarding under the “Security Section”.
    6. At the very, bottom of the page select remove for the ports that were forwarded.
    7. Select Apply to save changes.


    Firewall

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Advanced Setup on the main page.
    5. On the left hand side select Firewall under the “Security Section”.
    6. Disable Stealth Mode.
    7. Next select the Xbox IP address in the drop down for “Addressing Type”
    8. Select Low in the drop down for “Security Level”.
    9. Select Create Rule.
    10. Select both Traffic In and Traffic Out check boxes.
    11. Select Apply to save changes.


    How to Find Firmware Version

    1. Open a web browser on a computer.
    2. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    3. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    4. Select Modem Status on the main page.
    5. On the next page the current firmware will be located next to Firmware Version under “Modem Status”.


    Firmware Update

    Note: Firmware will be provided to you when you check for firmware update.

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Utilities on the main page.
    6. On the left hand side select Upgrade Firmware.
    7. Select the Download button to begin the firmware download to your computer.
    8. Once the download has completed select the Choose File or Browse
      option.
    9. Once you have selected the firmware downloaded to your computer. Select the
      Upgrade Firmware       button to begin the firmware update.
    10. Please be patient the update may take several minutes.


    Restore Factory Defaults

    From Hardware:

    1. Locate the back of the device, where the Ethernet port are located.
    2. Hold the reset button on the back for 30 seconds. You will need a paperclip, toothpick or pen to hold down the reset button.
    3. Let go of the reset button and wait about 1 minute for the device to reboot.


    From Firmware:

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Utilities on the main page.
    6. On the left hand side select Restore Defaults.
    7. Next to “Restore Modem to Factory Default State” select the Restore button.
    8. Wait for the device to reboot, this may take a few minutes.




    Entering PPPoE

    Note: You will need the have the PPPoE information beforehand. Contact your ISP if you need to collect this information.



    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Advanced Setup located on the left in red.
    6. Select WAN Settings from the left hand column. This option is located under the “IP Addressing” section.
    7. Under the “select the ISP protocol” Select the PPPoE option.
    8. Enter the PPP Username.
    9. Enter the PPP Password.
    10. Enter the same password into the Confirm PPP Password box.
    11. Verify PPP Auto Connect is enabled.
    12. Verify PPP Credentials Not Required is disabled.
    13. Verify Dynamic IP is selected.
    14. Verify Dynamic DNS is selected.
    15. Select the Apply button.
    16. The device will reboot.


    Known Issues

    There are no currently known issues with this device.



    Multiple console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    Device Manual

    Click here for the manual.

    :)
     
    XB1R Hydros, Jun 27, 2014
    #1
  2. hoitoy
    hoitoy Guest
    Connection interrupted

    Thanks for the reply I am running on a ZyXel C1000Z
     
    hoitoy, Jun 27, 2014
    #2
  3. taidara
    taidara Guest
    Suddenly can't connect to Internet on 360

    Greetings Phane7!

    May I ask, is your ZyXEL C1000Z operating in bridge mode, or router/NAT mode?

    If it's possible, can you try connect your Xbox directly in to the ZyXEL C1000Z, and verify if you can connect properly to Live, or not.

    Thanks!
     
    taidara, Jun 27, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Zyxel Zyxel C1000z: Overview