Zyxel: Bridging Guide/ Entering PPPoE

Discus and support Zyxel: Bridging Guide/ Entering PPPoE in XboX Networking Hardware to solve the problem; Zyxel (Modems/Gateways): Bridging Guide/ Entering PPPoE Login Information Gateway: 192.168.1.1 Username: admin Password: 1234 Entering PPPoE... Discussion in 'XboX Networking Hardware' started by XB1R Hydros, Jul 4, 2014.

  1. XB1R Hydros
    XB1R Hydros Guest

    Zyxel: Bridging Guide/ Entering PPPoE


    Zyxel (Modems/Gateways): Bridging Guide/ Entering PPPoE
    Login Information



    • Gateway: 192.168.1.1
    • Username: admin
    • Password: 1234
    Entering PPPoE

    Note: You will need the have the PPPoE information beforehand. Contact your ISP if you need to collect this information.



    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.1.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and type
      1234 for the password.
    5. Once logged in Select Network.
    6. Select the WAN Configuration option.
    7. Select the PPPoE option.
    8. Enter the PPP Username.
    9. Enter the PPP Password.
    10. Enter the PPPoE Service Name.
    11. Check the Enable NAT box.
    12. Check the Enable Full cone NAT box.
    13. Check the Enable Firewall box.
    14. Select the Next button. Continue to follow the prompts to save changes.
    15. The device will reboot.

    :)
     
    XB1R Hydros, Jul 4, 2014
    #1
  2. XB1R Hydros
    XB1R Hydros Guest
    Zyxel Zyxel C1000z: Bridging Guide/ Entering PPPoE

    Zyxel (Modems/Gateways) Zyxel C1000z: Bridging Guide/ Entering PPPoE
    Login Information



    • Gateway: 192.168.0.1
    • Username: admin
    • Password: (located on the bottom of the device)


    Entering PPPoE

    Note: You will need the have the PPPoE information beforehand. Contact your ISP if you need to collect this information.



    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address: 192.168.0.1 into the web address bar, select
      apply.
    4. This will take you to a login page, type admin for the username and password (located on the bottom of the device).
    5. Select Advanced Setup located on the left in red.
    6. Select WAN Settings from the left hand column. This option is located under the “IP Addressing” section.
    7. Under the “select the ISP protocol” Select the PPPoE option.
    8. Enter the PPP Username.
    9. Enter the PPP Password.
    10. Enter the same password into the Confirm PPP Password box.
    11. Verify PPP Auto Connect is enabled.
    12. Verify PPP Credentials Not Required is disabled.
    13. Verify Dynamic IP is selected.
    14. Verify Dynamic DNS is selected.
    15. Select the Apply button.
    16. The device will reboot.
     
    XB1R Hydros, Jul 4, 2014
    #2
  3. XB1R Athena
    XB1R Athena Guest
    Zyxel Zyxel PK5001Z: Bridging Guide

    Zyxel (Modems/Gateways) Zyxel PK5001Z: Bridging Guide
    Zyxel PK5001z



    Login Information

    Gateway - 192.168.0.1

    Username - none

    Password - none



    Bridging Guide



    *Bridge mode should only be used if you have a router to plug into the device.*

    *Please have PPPoE information available if needed to enter into the router (contact ISP if needed to get this information)*



    1. Open a web browser.
    2. Log into the router by entering the default gateway (192.168.0.1) into the address bar of the internet browser.
    3. Click on Quick Setup from the menu at the top.
    4. Scroll down and select Advanced IP Configuration.
    5. Select Transparent Bridging.
    6. Click Apply.
     
    XB1R Athena, Jul 4, 2014
    #3
  4. GMAN990 Win User

    ICMP Error

    Hi

    The Zyxel is a modem/router have you bridged the modem because if not you will suffer issues as you have two devices that are both NAT'ing otherwise , the Zyxel and the Netgear

    If you are not sure about bridging please contact your ISP as you may need additional details (PPPoE username/password) to enter into your Netgear before the change will work
  5. jmcode Win User

    Double NAT problems (I Think)

    Just to be clear, when you disabled DHCP on the Belkin, did you then connect the Zyxel to a LAN port on the Belkin? Did you verify the IP you used for port forwarding on the Zyxel was the new IP the Xbox One got from the Zyxel, not the one it had from the
    Belkin? If so, that should work unless something else is going on--can you get open NAT with the Xbox One directly wired to the Zyxel (with ports forwarded)? If not, that is a problem.

    As far as settings for bridge mode, I'm not familiar with your ISP so I'm not sue which setting is best on the Zyxel. On the Belkin, you need to match the current ISP setting on the Zyxel--i.e. if Zyxel is using PPPoE, set the Belkin to that. You will probably
    need to enter authentication (user/pass) depending on what that setting is...
  6. 2340293u oifjdsohf Win User

    Zhone: Bridging Guide

    With ISP distributel - a factory restore will set bridge mode, PPPOE login info will need to be entered into router to regain web access.
  7. XBR Dionysus Win User

    My wired connection wont work to my 360

    Sorry for the late post but if the computer works on all the ports but nothing else does it sound like the PPPoE information somehow got removed from the Zyxel and got put into the computer.

    Some DSL companies use an authentication called PPPoE, it's a user name and a password that is issued by the ISP and is normally entered into the gateway. If it gets removed or changed then you will not get internet to the house. If the PPPoE is entered
    into the comp or the console then that device will connect. I would call Telus and have them restore the gateway and if needed they can reset up the PPPoE. If that doesn't work then they might not use those settings if that’s the case then I would suggest
    they replace the device. Hope that helps.
  8. XBR Poseidon Win User

    Netgear Netgear 7550: Bridging Guide

    The PPPoE information will need to be entered into your router for the bridge to work. For further assistance please post in the support forums specific to your console. These forums are meant to be informational only.
Thema:

Zyxel: Bridging Guide/ Entering PPPoE

Loading...

  1. Zyxel: Bridging Guide/ Entering PPPoE - Similar Threads - Zyxel Bridging Guide

  2. Cloud gaming has screen tearing with high speed wired internet, Zyxel modem issue?

    in XBoX Games and Apps
    Cloud gaming has screen tearing with high speed wired internet, Zyxel modem issue?: Hello, I'm trying to understand why I have continuous screen tearing when I game in the cloud. I have the following setup: Xbox series X Cabled internet, when testing on console Download 89...

  3. How do i configure my zyxel router from ivp4 to ipv6?

    in XboX Networking Hardware
    How do i configure my zyxel router from ivp4 to ipv6?: How do i configure my zyxel router from ivp4 to ipv6? They have a knowledge base you can find with a simple Google search. How to Set Up IPv6 Interfaces for Pure IPv6 Routing...

  4. Is anyone willing to help with Zyxel C1100Z setup for Red Dead Redemption 2 Online on Xbox One?

    in XboX Networking Hardware
    Is anyone willing to help with Zyxel C1100Z setup for Red Dead Redemption 2 Online on Xbox One?: Is anyone willing to help with Zyxel C1100Z setup for Red Dead Redemption 2 Online on Xbox One? Thanks for the reply, I am using wireless. bdd10a5f-681e-46a8-ae32-30c45a5d8bd1

  5. Zyxel C1000z: ZyXEL C3000Z Router/Modem isn't seen by Xbox One

    in XboX Networking Hardware
    Zyxel C1000z: ZyXEL C3000Z Router/Modem isn't seen by Xbox One: Zyxel C1000z: ZyXEL C3000Z Router/Modem isn't seen by Xbox One Do you have an original launch Xbox One? If so that may be the issue as that router uses 802.11ac and that is only supported on the S...

  6. Zyxel C1000z: Xbox One upnp failing

    in XboX Networking Hardware
    Zyxel C1000z: Xbox One upnp failing: Zyxel C1000z: Xbox One upnp failing As already mentioned, www.portforward.com is a fantastic resource. It lets you search for your specific router, and has step by step guides that are very clear,...

  7. Zyxel Zyxel NBG-415N: How to change mtu settings

    in XboX Networking Hardware
    Zyxel Zyxel NBG-415N: How to change mtu settings: Zyxel (Routers) Zyxel NBG-415N: How to change mtu settings MTU, needs to meet a minimum of 1384 MTU or higher to play games on Xbox Live. Checking and adjusting your router settings could quickly...

  8. Zyxel Zyxel VSG1432: Zyxel VMG8823

    in XboX Networking Hardware
    Zyxel Zyxel VSG1432: Zyxel VMG8823: Zyxel (Modems/Gateways) Zyxel VSG1432: Zyxel VMG8823 Hi, you only get ipv6 if your internet provider supports it. If it does, then your Xbox One would automatically use it....

  9. Zyxel Zyxel 660 Series: Setting up WiFi

    in XboX Networking Hardware
    Zyxel Zyxel 660 Series: Setting up WiFi: Zyxel (Modems/Gateways) Zyxel 660 Series: Setting up WiFi I am trying to connect to my WiFi. XBox will not accept my password to our network. We received a new modem today because our old one...

  10. Zyxel Zyxel C1000z: problems connecting to wifi

    in XboX Networking Hardware
    Zyxel Zyxel C1000z: problems connecting to wifi: Zyxel (Modems/Gateways) Zyxel C1000z: problems connecting to wifi brand new xbox with built in wireless. sees wifi but keeps saying password is wrong...all other devices have no problem connecting...