Xbox 360 Media Remote TV code

Check this:
http://support.xbox.com/en-US/xbox-360/accessories/media-remote



Scan for a TV code

You can send a sequence of codes to from your remote to your TV to find the right code for your TV, if you do not know it.

1. Turn on your TV and point the media remote toward it.
2. Press and hold the Mute and 5 buttons simultaneously for two seconds to enter TV programming mode.
   
3. Press the Channel Up button repeatedly to send one code per button press from your media remote to your TV. By pressing Channel Up, you advance the code each time.
   
4. When the correct code is sent from the media remote to your TV, your TV will turn off. Press the Select button to confirm your code.
   

support.xbox.com/.../media-remote

Scan for a TV code

You can send a sequence of codes to from your remote to your TV to find the right code for your TV, if you do not know it.

Turn on your TV and point the media remote toward it.

Press and hold the Mute and 5 buttons simultaneously for two seconds to enter TV programming mode.

Press the Channel Up button repeatedly to send one code per button press from your media remote to your TV. By pressing Channel Up, you advance the code each time.

When the correct code is sent from the media remote to your TV, your TV will turn off. Press the Select button to confirm your code.

If your TV turns off but you then accidently continue to press Channel Up to continue past the correct code, press Channel Down to go back to the correct code. Your TV will turn on again when you go back to the correct code. Press the Select button to confirm
your code.

Hello. If you can control your soundbar's volume using your TV remote, then use the TV code for your TV on the Xbox 360 remote and see if it works. I have linked to the appropriate pages for the NEWER remote.



B&W (Bowers and Wilkins) are NOT a listed manufacturer under the codes section. If you spent $2,000+ on a B&W Panorama Soundbar, it might be a better idea to spend a couple hundred on a better Universal Remote such as the Harmony Line from Logitech that
has a wide list of supported brands and learning functionality.



Xbox Media Remote:



Setup Page:
support.xbox.com/.../media-remote

Codes:
download.microsoft.com/.../Xbox_360_Media_Remote_New_TV_Codes.pdf





Based on the information I found about your specific soundbar it has the capability to be controlled by your TV's remote control assuming your TV supports those features. If you have the capability to use your TV remote to control the volume of your soundbar,
then it's possible that the TV code for your TV can be used for this soundbar via the Xbox 360 media remote.



Even if there was a Bowers and Wilkins code for this remote, you would lose the ability to control your TV as you can only program 1 device at a time for this remote.

Hello Jesscollie,

the process needed to set up the remote can be found on the two pages below, but I would sugges scanning for the TV code with the following process

Scan for a TV code

You can send a sequence of codes to from your remote to your TV to find the right code for your TV, if you do not know it.

1. Turn on your TV and point the media remote toward it.
2. Press and hold the Mute and 5 buttons simultaneously for two seconds to enter TV programming mode.
   
3. Press the Channel Up button repeatedly to send one code per button press from your media remote to your TV. By pressing
   Channel Up, you advance the code each time.
4. When the correct code is sent from the media remote to your TV, your TV will turn off. Press the
   Select button to confirm your code.

If your TV turns off but you then accidently continue to press Channel Up to continue past the correct code, press
Channel Down to go back to the correct code. Your TV will turn on again when you go back to the correct code. Press the
Select button to confirm your code.



support.xbox.com/.../media-remote - this one also contains is list of all the codes for TVs

support.xbox.com/.../universal-media-remote



Please come back and let us know if this worked



thanks

Hello gamer:

To scan for the correct TV code, follow these steps:

Turn on the TV, and then point the remote control toward the TV.

Press and hold the TV button and the OK button at the same time for two seconds. All the buttons on the remote control will illuminate for two seconds. Then, only the numeric TV buttons (1 through 12) remain illuminated.

Press the CH+ button or the CH– button to send a series of off commands to the TV. Continue to press the CH+ button or the CH– button until the TV turns off.

Note Give enough time for the TV to respond to the off command after you press each button. Some TVs take more time to react to the off command than other TVs.

Press the TV button to save the code and to exit. All the buttons on the remote control will blink three times to confirm the code.

Note If the remote control doesn't function correctly after you set the TV code, try a different code from the same TV manufacturer. Or, scan for another code.

You can only use the Xbox 360 Universal Media Remote with the Xbox 360 console, TVs, or a Windows XP Media Center computer. You cannot use the Xbox 360 Universal Media Remote with VCRs, DVRs, DVD players, or other audio equipment.