TP-Link: Overview

Discus and support TP-Link: Overview in XboX Networking Hardware to solve the problem; TP-Link (Modems/Gateways): Overview TP-Link TD-W8901G Login Information: Default Gateway – 192.168.1.1 Username – admin Password – admin How to... Discussion in 'XboX Networking Hardware' started by XBR Poseidon, Mar 15, 2015.

  1. XBR Poseidon
    XBR Poseidon Guest

    TP-Link: Overview


    TP-Link (Modems/Gateways): Overview
    TP-Link TD-W8901G

    Login Information:

    Default Gateway – 192.168.1.1

    Username – admin

    Password – admin



    How to Find SSID (Network Name)



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface setup from the tabs across.
    4. Select Wireless from the resulting submenu.
    5. The wireless network name is located next to SSID in the WPS Settings section.


    How To Find Wireless Passphrase (WPA/WEP)



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface setup from the tabs across.
    4. Select Wireless from the resulting submenu.
    5. The wireless passphrase will be located in the pre-shared key space.


    Changing Wireless Security Type/ Disabling Wireless Security



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface setup from the tabs across.
    4. Select Wireless from the resulting submenu.
    5. Select Disabled from the Authentication Type drop down menu.
    6. Click the Save button at the bottom of the screen.


    MAC Filtering



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface setup from the tabs across.
    4. Select Wireless from the resulting submenu.
    5. Select Deactivated from the Wireless MAC Address Filter section.
    6. Click the Save button at the bottom of the screen.


    Change Wireless Mode



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface setup from the tabs across.
    4. Select Wireless from the resulting submenu.
    5. Select 802.11g from the Wireless Mode drop down.
    6. Click the Save button at the bottom of the screen.


    Change Wireless Channel



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface setup from the tabs across.
    4. Select Wireless from the resulting submenu.
    5. Select the desired wireless channel from the channel drop down. (1,3,9,11)
    6. Click the Save button at the bottom of the page.


    DHCP Reservation



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface Setup from the menu at the top.
    4. Select LAN from the resulting submenu.
    5. In the DHCP Table section select the desired IP Address from the IP Address drop down menu.
    6. Enter the MAC Address of your console in the MAC Address field.
    7. Select Static from the Status drop down.
    8. Click Save at the bottom of the page.


    UPnP



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Access Management from the menu at the top.
    4. Select UPnP from the resulting submenu.
    5. Toggle both UPnP and Auto-config to Activated or Deactivated depending on need.
    6. Click the Save button at the bottom of the page.


    DMZ



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Advanced Setup from the menu at the top.
    4. Select NAT from the resulting submenu.
    5. Select DMZ.
    6. Set the DMZ to Enabled and then enter the IP Address of your Xbox console.
    7. Click the SAVE button found at the bottom of the screen.


    Disable DMZ



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Advanced Setup from the menu at the top.
    4. Select NAT from the resulting submenu.
    5. Select DMZ.
    6. Set the DMZ to Disabled.
    7. Click the SAVE button at the bottom of the screen.


    Port Forwarding



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Advanced Setup from the menu at the top.
    4. Select NAT from the resulting submenu.
    5. Select Virtual Server.
    6. Set the Rule Index to a value of 1 through 10.
    7. Set Application to other or user defined.
    8. Set Protocol to ALL.
    9. Enter 3074 for the Start Port Number and the End Port Number.
    10. Enter the IP Address of your Xbox Console in the Local IP Address field.
    11. Click the Save button at the bottom of the screen.


    Disable Port Forwarding



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Advanced Setup from the menu at the top.
    4. Select NAT from the resulting submenu.
    5. Select Virtual Server.
    6. Enter the Index of the entry you want to delete and click Delete.
    7. Click the Save button at the bottom of the screen.


    Firewall



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Advanced Setup from the menu at the top.
    4. Select Firewall from the resulting submenu.
    5. Set both Firewall and SPI to disabled.
    6. Click the Save button.


    Restoring Factory Defaults

    Through Firmware



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Maintenance from the menu at the top.
    4. Select SysRestart from the resulting submenu.
    5. Select Factory Default Settings.
    6. Click the RESTART button.


    Through Hardware



    1. Locate the reset button on the back of the device.
    2. Using a pin or similar small object press and hold the reset button for a minimum of 5 seconds.


    How to Find Firmware Version



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Maintenance from the menu at the top.
    4. Select Firmware from the resulting submenu.
    5. The current firmware version is listed next to Current Firmware Version.


    Firmware Update



    1. Locate an updated firmware file either from your Internet Service Provider or from
      TP-Link France - Equipements réseau Wi-Fi pour particuliers et professionnels
    2. Download the new firmware to your computer.
    3. Connect your computer to the router via an Ethernet cable.
    4. Open a web browser and type http://192.168.1.1 into the address and press enter.
    5. Enter “admin” for both the username and password when prompted.
    6. Select Maintenance from the menu at the top.
    7. Select Firmware from the resulting submenu.
    8. Click the Browse button and locate the file you saved on your computer.
    9. Click the UPGRADE button at the bottom of the screen.
    10. Wait for the update to complete. Your device may restart several times.






    Bridging Guide



    1. Open a web browser and type http://192.168.1.1 into the address and press enter.
    2. Enter “admin” for both the username and password when prompted.
    3. Select Interface Setup from the menu at the top.
    4. Select Internet from the resulting submenu.
    5. In the Encapsulation section Choose Bridge Mode.
    6. Click the SAVE button at the bottom of the screen.


    Multiple Console Support



    We have no confirmed cases where multiple consoles were able to obtain an Open NAT state while using this device. Please comment on this page if you have been able obtain Open NAT on two or more consoles using this device.



    Known Issues



    This device has no known issues at this time.



    Device Manual



    The device manual can be found
    here    .

    :)
     
    XBR Poseidon, Mar 15, 2015
    #1
  2. XB1R Apollo
    XB1R Apollo Guest
    TP-Link: Overview

    TP-Link (Modems/Gateways): Overview
    TP-Link TD-W8960N

    Login Information

    • Gateway - 192.168.1.1
    • Username - admin
    • Password - admin



    How to Find SSID (Network Name)

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Wireless from the menu on the left.
    6. Select Basic from the submenu.
    7. The Network Name (SSID) will be displayed next to SSID. The network name can be changed in this space.
    8. Click the Apply/Save button at the bottom of the page if any changes were made.




    How To Find Wireless Passphrase (WPA/WEP)

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Wireless from the menu on the left.
    6. Select Security from the submenu.
    7. The Wireless Passphrase will be displayed next to WPA Pre-Shared Key. You may need to click the Click here to display link.




    Changing Wireless Security Type/ Disabling Wireless Security

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Wireless from the menu on the left.
    6. Select Security from the submenu.
    7. The Wireless Security can be disabled by selecting “Open” from the Network Authentication drop down.
    8. Click the Apply/Save button at the bottom of the page.




    MAC Filtering

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Wireless from the menu on the left.
    6. Select MAC Filter from the sub-menu.
    7. Select Disabled from the MAC Restrict Mode.




    Changing Wireless Channel

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Wireless from the menu on the left.
    5. Select Advanced from the submenu.
    6. From the drop down menu labeled Channel ID select the desired Channel. (Channels 1,3,9,11)
    7. Select the Apply/Save button.




    Changing Wireless Mode

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Wireless from the menu on the left.
    5. Select Advanced from the submenu.
    6. Select 54g Performance in the Mode dropdown.
    7. Select the Apply/Save button.




    Change Wireless Band (width)

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Wireless from the menu on the left.
    5. Select Advanced from the submenu.
    6. Select the 20MHz option from the bandwidth dropdown box.
    7. Select the Apply/Save button.




    DHCP Reservation

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu on the left.
    5. Select LAN from the submenu.
    6. Click the Add Entries button.
    7. Type the consoles MAC address and desired IP address.
    8. Select the Apply/Save button.




    UPnP

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu on the left.
    5. Select UPnP from the submenu.
    6. Check or un-check the option for UPnP.
    7. Select the Apply/Save button.




    DMZ

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu on the left.
    5. Select NAT from the submenu.
    6. Select DMZ Host from the next submenu.
    7. Enter the IP Address of the Xbox.
    8. Select the Apply/Save button.


    Disable DMZ

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu on the left.
    5. Select NAT from the submenu.
    6. Select DMZ Host from the next submenu.
    7. Clear the IP Address from the DMZ Host IP Address.
    8. Select the Apply/Save button.
    Port Forwarding

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu on the left.
    5. Select NAT from the submenu.
    6. Select Virtual Servers from the next submenu.
    7. Click the Add button.
    8. Enter a custom Server name. Something like "XBL" or "Xbox Live".
    9. Enter the IP address of the console into the Server IP Address.
    10. In the four columns asking for the port number enter 3074.
    11. Set Protocol to both.
    12. Select the Apply/Save button.


    Disable Port Forwarding

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu on the left.
    5. Select NAT from the submenu.
    6. Select Virtual Servers from the next submenu.
    7. Check the box next to the Xbox Live entries under the remove column.
    8. Click the Remove button at the top.
    9. Select the Apply/Save button.




    Firewall

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu on the left.
    5. Select WAN from the submenu.
    6. Select Add.
    7. Un-Check Enable Firewall.
    8. Be sure the PPP Username and PPP Password are still in place.
    9. Click the Next button.
    10. On the following Summary screen click the Save button.




    How to Find Firmware Version

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Device Info from the menu on the left.
    5. The Firmware Version is listed to the right of Firmware Version.




    Firmware Update

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Management.
    5. Select Update Software.
    6. Click the browse button.
    7. Select the Firmware file you downloaded.
    8. Click the Update Software button.
    9. Wait for the device to restart.




    Restoring Factory Defaults



    Through firmware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Management.
    6. Select Settings.
    7. Select Restore Default.
    8. Click the Restore Default Settings button.
    9. Wait for the device to reset and restart.


    Through Hardware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.




    Bridging Guide

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Layer2 Interface from the menu on the left.
    6. Select ATM Interface from the submenu.
    7. Leave the VPI and VCI on their default values.
    8. Select EoA from DSL Link Type options.
    9. Select LLC/SNAP-BRIDGING.
    10. The rest of the options should be left to the default values.
    11. Click the Apply/Save button.




    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.

    Known Issues

    No Known Issues.





    Device Manual

    TD-W8960N V3

    TD-W8960N V4
     
    XB1R Apollo, Mar 15, 2015
    #2
  3. XB1R Apollo
    XB1R Apollo Guest
    TP-Link: Overview

    TP-Link (Modems/Gateways): Overview
    TP-Link TD-8616



    Login Information

    • Gateway - 192.168.1.1
    • Username - admin
    • Password - admin



    How to Find SSID (Network Name)

    *This device does not have wireless capability*





    How To Find Wireless Passphrase (WPA/WEP)

    *This device does not have wireless capability*





    Changing Wireless Security Type/ Disabling Wireless Security

    *This device does not have wireless capability*





    MAC Filtering

    *This device does not have wireless capability*





    Change Wireless Channel

    *This device does not have wireless capability*





    Change Wireless Mode

    *This device does not have wireless capability*





    Change Wireless Band (width)

    This device does not have any wireless settings.





    DHCP Reservation

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Interface Setup from the menu at the top.
    5. Select LAN from the submenu.
    6. Under the section titled DHCP Table select the desired IP Address from the dropdown labeled IP Address.
    7. Enter the MAC Address of the Xbox.
    8. Select the Save button.




    UPnP

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Access Management from the menu at the top.
    5. Select UPnP from the submenu.
    6. Select Activated next to UPnP and Auto-configured.
    7. Select the Save button.




    DMZ

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu at the top.
    5. Select NAT from the submenu.
    6. Select DMZ from the next submenu.
    7. Select Enabled next to DMZ.
    8. Enter the IP Address of the Xbox.
    9. Select the Save button.


    Disable DMZ

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu at the top.
    5. Select NAT from the submenu.
    6. Select DMZ from the next submenu.
    7. Select Disabled.
    8. Click the Save button at the bottom.




    Port Forwarding

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu at the top.
    5. Select NAT from the submenu.
    6. Select Virtual Server from the next submenu.
    7. Select All for the Protocol.
    8. Enter 3074 for the Start Port Number and End Port Number.
    9. Enter the IP Address of the Xbox.
    10. Select the Save button.


    Disable Port Forwarding

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu at the top.
    5. Select NAT from the submenu.
    6. Select Virtual Server from the next submenu.
    7. Enter the Index number of an entry.
    8. Click the DELETE button.




    Firewall

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Advanced Setup from the menu at the top.
    5. Select Firewall from the submenu.
    6. Select Disabled next to Firewall and SPI.
    7. Select the Save button.




    How to Find Firmware Version

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Maintenance from the menu at the top.
    5. Select Firmware from the submenu.
    6. The Firmware Version will be listed next to Current Firmware Version.




    Firmware Update

    1. Open a web browser.
    2. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    3. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    4. Select Maintenance from the menu at the top.
    5. Select Firmware from the submenu.
    6. Select Browse next to New Firmware Location.
    7. Locate the downloaded firmware file.
    8. Select Upgrade.




    Restoring Defaults



    Through firmware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Maintenance from the menu at the top.
    6. Select SysRestart from the submenu.
    7. Select Factory Default Settings.
    8. Select the Restart button.


    Through Hardware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.




    Bridging Guide

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Log into the device by entering the default gateway into the address bar of the internet browser (192.168.1.1).
    4. The device will then prompt you to enter the username and password. The default username and password are "admin" and "admin".
    5. Select Interface Setup from the tabs at the top.
    6. Select Internet from the sub-menu.
    7. Select Bridge Mode from the Encapsulation section of the page.
    8. Click the SAVE button from the bottom of the page.




    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.





    Known Issues

    No known issue.





    Device Manual

    Click
    here
     
    XB1R Apollo, Mar 15, 2015
    #3
  4. prju68 Win User

    TP-Link: TP Link archer VR2600

    My advice would be if you need to do multiplayer that you send the router back. It does not work with XBOX.

    I have tried UPNP, DMZ, and manually forwarding all the ports. Nothing works.

    I did manage to get the DMZ to work for a few days and then it stopped.

    To be fair to TP-LINK I don't think the problem is theirs I think it is the XBOX as the DMZ and port forwarding works with other servers and other services. By all means contact the TP-LINK support they are very helpful, and perhaps they can get Microsoft
    to help
  5. FaTnFuRiOusFLiP Win User

    D-Link: Overview

    Just bridge my twc ubee gateway to my dir655 had to ajusted a few settings and found out I had hard ware version dlink 655 a4 the firmware was to out of date but still was able to connect 2 xb1 via cat6 wire..make sure u get dir 655 b or c.. hardware bottom
    of router tag will say (h/v a,) --trouble connecting (h /v b, h/v c) ,... ect. But I got my 655 working nat type open both xb1
  6. AtomicMeltdown0 Win User

    D-Link: Overview

    Do you know how to get an open NAT type on the Xbox One with this router?
  7. DeathDealer7227 Win User

    wired xbox live disconnects

    tp-link tl-WR940N is the model
  8. CC SURFER X Win User

    Which router are u using?

    Dual band routers seem to be the way of the future for multimedia and such. I recommend the TP LINK ARCHER C7 or otherwise known as the TP Link AC1750 Wireless Dual Band Gigabit Router. Good luck with your search.
Thema:

TP-Link: Overview

Loading...

  1. TP-Link: Overview - Similar Threads - Link Overview

  2. Hi Microsoft, I have a minecraft account linked to the email *** Die E-Mail-Adresse wurde...

    in XBoX Accessibility
    Hi Microsoft, I have a minecraft account linked to the email *** Die E-Mail-Adresse wurde...: I don't understand why this would be, because I have used this email address for Microsoft many years before, but now it does not work. Can you please get back to me on this, and if it matters the...

  3. How do I link my PlayStation account onto Minecraft?

    in XBoX Accessibility
    How do I link my PlayStation account onto Minecraft?: my PlayStation is not letting me sign into my Microsoft account on Minecraft, saying that I alr have an account linked to it but the problem is, THERE ARE NO ACCOUNTS so I need help trying to fix...

  4. How do I find my linked game accounts on Microsoft

    in XBoX Accessibility
    How do I find my linked game accounts on Microsoft: For example I want to delete my minecraft account and create a new one 3aa7d073-a988-4131-a23c-4ce5d33fb03c

  5. Is there a way I can redirect private server links on Roblox from my browser to the app...

    in XBoX Games and Apps
    Is there a way I can redirect private server links on Roblox from my browser to the app...: I have S mode enabled from a previous owner and can't turn it off. This disables me from getting the official Roblox for my browser. I've been trying for a while now and still can't figure out how...

  6. Can't Log Into Microsoft Account on Console – False "Already Linked" Error

    in XBoX Accessibility
    Can't Log Into Microsoft Account on Console – False "Already Linked" Error: Hey everyone, I’ve played Minecraft for countless hours on console, but now I’m unable to log into my Microsoft account. I keep getting the error: "Oops! Your Microsoft account is already logged...

  7. Microsoft linking wont work how do i fix it?

    in XBoX Accessibility
    Microsoft linking wont work how do i fix it?: I play on my playstation 5 and just bought playstation plus so i can play with friends. I made a brand new microsoft account wich has not been used for anything yet and tried connecting it with my...

  8. how to link my xbox rainbow six siege account to my pc rainbow six siege account without...

    in XBoX Games and Apps
    how to link my xbox rainbow six siege account to my pc rainbow six siege account without...: how to link my xbox rainbow six siege account to my pc rainbow six siege account without using my Xbox as I no longer use it ? every tutorial i watch tells me that i need to load up r6 on my...

  9. How to link Microsoft account to Minecraft on ps5?

    in XBoX Accessibility
    How to link Microsoft account to Minecraft on ps5?: Had a PlayStation 4, which was connected to a Microsoft account. Recently, I purchased a PlayStation 5 and transferred the data from the PlayStation 4 to the PlayStation 5. I tried to connect my...

  10. D-Link: Overview

    in XboX Networking Hardware
    D-Link: Overview: D-Link (Routers): Overview D-Link DIR-868L Login Information Gateway - 192.168.0.1 or http://dlinkrouter/ Username - Admin Password - (blank) How to Find SSID (Network Name) Plug the...