Siemens: Overview

Discus and support Siemens: Overview in XboX Networking Hardware to solve the problem; Siemens (Modems/Gateways): Overview Siemens Speedstream 5x00 Series Login Information Gateway - 192.168.254.254 Username - admin Password –... Discussion in 'XboX Networking Hardware' started by XB1R Hades, Sep 12, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Siemens: Overview


    Siemens (Modems/Gateways): Overview
    Siemens Speedstream 5x00 Series



    Login Information

    • Gateway - 192.168.254.254
    • Username - admin
    • Password – (created during initial setup)
    How to Find SSID (Network Name)



    Not Available.



    How To Find Wireless Passphrase (WPA/WEP)



    Not Available.



    Changing Wireless Security Type/ Disabling Wireless Security



    Not Available.



    MAC Filtering



    Not Available.



    Change Wireless Channel



    Not Available.



    Change Wireless Mode



    Not Available.



    DHCP Reservation



    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter admin for the user name and your created password.
    3. Under the section titled Setup select DHCP from the menu on the left.
    4. Under the section labeled "IP Reserved Addresses" enter the IP Address and MAC Address of the Xbox.
    5. Select Apply.


    UPnP



    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter the admin for the username and your created password.
    3. Select UPnP from the left menu.
    4. Toggle UPnP.


    DMZ



    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter admin for the user name and your created password.
    3. Under the section titled setup, select firewall from the menu on the left.
    4. Select DMZ.
    5. Select the second “enable DMZ with this host IP address:”
    6. Select the IP address of the xbox from the drop down.
    7. Select Apply.


    Disable DMZ



    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter admin for the user name and your created password.
    3. Under the section titled setup, select firewall from the menu on the left.
    4. Select DMZ.
    5. Select Disable DMZ.
    6. Select Apply.


    Port Forwarding



    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter the admin for the username and your created password.
    3. Under the section titled setup, select port forwarding from the menu on the left.
    4. In the section that is titled Add/Edit Entry, select TCP from the drop-down menu and enter in “3074” for the boxes that say “TCP/UDP port(s)”.
    5. Select the button next to “redirect selected protocol/service to IP Address” and enter in the IP address of the console in the box to the right of it.
    6. Select Apply.


    Disable Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter the admin for the username and your created password.
    3. Under the section titled setup, select port forwarding from the menu on the left.


    Firewall



    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter the admin for the username and your created password.
    3. Under the section titled setup, select firewall from the menu on the left and then filter ruled from the submenu.
    4. Uncheck enabled attack detection system.
    5. Select Apply.


    How to Find Firmware Version



    Not Available.



    Updating Firmware



    Firmware updates are installed automatically by the Internet Service Provider



    Restore Defaults



    *Please have PPPoE information available, if you do not have this, please contact your ISP.*



    Through firmware



    This option is not available.



    Through Hardware



    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the back of the device.
    3. Using a paperclip press and hold the reset button for 30 seconds.
    4. Wait for the device to restart.


    Bridging Guide



    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open a web browser.
    3. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted enter the admin for the username and your created password.
    4. 192.168.254.254/brgmode.htm
    5. Click the Apply button.
    6. Click the Reboot button.


    Multiple Console Support



    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    Known Issues



    No known issues

    Device Manual

    Click here for the manual.

    :)
     
    XB1R Hades, Sep 12, 2014
    #1
  2. XB1R Athena
    XB1R Athena Guest
    Siemens: Overview

    Siemens (Modems/Gateways): Overview
    Siemens 4300

    Login Information

    Gateway - 192.168.254.254

    Username - admin

    Password – admin



    How to Find SSID (Network Name)



    *This device does not have wireless capability*



    How To Find Wireless Passphrase (WPA/WEP)



    *This device does not have wireless capability*



    Changing Wireless Security Type/ Disabling Wireless Security



    *This device does not have wireless capability*



    MAC Filtering



    *This device does not have wireless capability*



    Change Wireless Channel



    *This device does not have wireless capability*



    Change Wireless Mode



    *This device does not have wireless capability*



    DHCP Reservation



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Under the section titled Setup, select DHCP from the menu on the left.
    4. Under IP Reserved Addresses enter the IP Address and MAC Address of the Xbox.
    5. Select Save Settings.


    UPnP



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Under the section titled setup, select UPnP.
    4. Select enable full Internet Gateway Device Support.
    5. Select Apply.


    DMZ



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Under the section titled setup, select firewall from the menu on the left.
    4. Select DMZ.
    5. Select “Enable DMZ with this host IP address:”
    6. Enter in the IP address of the Xbox in the box.
    7. Select Apply.


    Disable DMZ



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Under the section titled setup, select firewall from the menu on the left.
    4. Select DMZ.
    5. Select Disable DMZ.
    6. Select Apply.


    Port Forwarding



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. In the section that is titled Add/Edit Entry, select TCP from the drop-down menu and enter in “3074” for the boxes that say “TCP/UDP port(s)”.
    4. Select the button next to “redirect selected protocol/service to IP Address” and enter in the IP address of the console in the box to the right of it.
    5. Select Apply.


    Disable Port Forwarding



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Find the port you want to remove and select Delete.
    4. Select Apply.


    Firewall



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Under the section titled setup, select firewall from the menu on the left and then filter ruled from the submenu.
    4. Uncheck enabled attack detection system.
    5. Select Apply.


    Firmware Update



    *Firmware updates are installed automatically by the Internet Service Provider.*



    How to Find Firmware Version



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Select Status and Statistics.
    4. Select System Summary.
    5. The firmware is located on this page labeled Firmware Part #.


    Restore Factory Defaults



    Through firmware



    *This option is not available.*



    Through Hardware



    1. Locate the reset button on the back of the device.
    2. Using a toothpick or ballpoint pen press and hold the reset button for 30 seconds.
    3. Wait for the device to restart.


    Bridging Guide



    1. Open a web browser.
    2. Enter 192.168.254.254 into the address bar. When prompted enter admin for the user name and admin for the password.
    3. Select Setup on the left.
    4. Click on WAN Interface.
    5. On this page select OE BRG.
    6. Select RFC-2684 Bridged.
    7. Click on Finish.
    8. For this to take effect click on the REBOOT link at the bottom.


    Multiple Console Support



    We have confirmed that this network device is unable to support more than one console with an Open NAT.

    Known Issues



    No known issues at this time.





    Device Manual



    Under Construction.
     
    XB1R Athena, Sep 12, 2014
    #2
  3. XB1R Athena
    XB1R Athena Guest
    Siemens: Overview

    Siemens (Modems/Gateways): Overview
    Siemens 6520

    Login Information

    • Gateway - 192.168.254.254
    • Username - admin
    • Password – admin/wirelessdsl



    Wireless Security

    How to Find Wireless Passphrase

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Home Network from the menu on the left.
    5. Select Advanced Settings.
    6. Select “Configure the Local SpeedStream Gateway Wireless Network”.
    7. The passphrase is located on this page labeled Security Key Info.
    How to Change Wireless Security

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Home Network from the menu on the left.
    5. Select Advanced Settings.
    6. Select “Configure the Local SpeedStream Gateway Wireless Network”.
    7. Select Begin Wireless Wizard.
    8. Select Next.
    9. Select Next.
    10. There is no option to change the security type on the page, but you can skip the page to select desired security type. (To turn off the security select Open System for the Authentication on each page.)
    11. Select Finish.


    DMZ

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Security from the menu on the left.
    5. Select Firewall Settings.
    6. Put a check in the DMZ box.
    7. Select the Customize button to the right.
    8. Select “Enable DMZ with this host IP address”
    9. Select the Xbox from the drop down menu.
    10. Select Apply.
    11. Return to the Firewall page to make sure the DMZ is enabled then click Apply.
    Disable DMZ

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Security from the menu on the left.
    5. Select Firewall Settings.
    6. Uncheck the DMZ box.
    7. Select Apply.


    Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Security on the left.
    5. Select the Customize button next to IP Filtering.
    6. Select the Add New IP Filter Rule button.
    7. Type up to a five digit number to name your rule in the Rule No box.
    8. Select Permit in the Access drop down menu.
    9. For the Direction drop down select either Outbound or Inbound. (Note you will have to make two rules one for Outbound and one for Inbound)
    10. Select Next.
    11. If Outbound was selected on the last page, in the Source window select the Xbox from the drop down menu and Any IP Address in the Destination window.
    12. If Inbound was selected on the last page, in the Source window select Any IP Address and in the Destination window select the Xbox from the drop down menu.
    13. Select Next.
    14. For both Inbound and Outbound options, select Any in the Select By Name drop down menu.
    15. Select Next.
    16. Again for both Inbound and Outbound, select “equal to” in both the Source and Destination Port Operator drop downs.
    17. Type 3074 in all four Port boxes.
    18. Select Next.
    19. Select Finish.
    Disable Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Security on the left.
    5. Select the Customize button next to IP Filtering.
    6. Select the Delete All button.


    Firewall

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Security on the left.
    5. Select the Customize button next to Level.
    6. Select Low or Off in the drop down menu.
    7. Select Apply.


    Restore Defaults

    Through firmware

    *This option is not available.*

    Through Hardware

    1. Locate the reset button on the back of the device.
    2. Using a toothpick or ballpoint pen press and hold the reset button for 30 seconds.
    3. Wait for the device to restart.


    Firmware Update


    *Firmware is updated automatically by the ISP*

    How to Find Firmware Version

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. The firmware is located on this page labeled Firmware Part #.


    Change Wireless Mode

    *This option is not available.*



    Change Wireless Channel

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Home Network from the menu on the left.
    5. Select Advanced Settings.
    6. Select “Configure the Local SpeedStream Gateway Wireless Network”.
    7. Select Begin Wireless Wizard.
    8. Select desired channel in the Channel drop down. (1,3,9,11)
    9. Select Finish.


    UPnP

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Home Network from the menu on the left.
    5. Select Advanced Settings.
    6. Select “Configure the Local SpeedStream Gateway UPnP”.
    7. Select Enable full Internet Gateway Device. (To turn off the UPnP select Disable UPnP)
    8. Select Apply.
    9. Click Reboot.


    DHCP Reservation

    *DHCP Reservation is not available on this device.*



    Bridging Guide

    *Contact ISP for bridging instructions if supported.*



    MAC Filter

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Home Network from the menu on the left.
    5. Select Advanced Settings.
    6. Select “Configure the Local SpeedStream Gateway Wireless Network”.
    7. Select Begin Wireless Wizard.
    8. Select Next.
    9. Select Disable for Wireless Filter.
    10. Select Finish.


    How to Find SSID (Network Name)

    1. Open a web browser.
    2. Enter http://192.168.254.254 into the address bar. (Or click the link) When prompted, enter in “admin” for the username and “admin” or “wirelessdsl”
      for the password.
    3. Select Gateway from the menu at the top.
    4. Select Home Network from the menu on the left.
    5. Select Advanced Settings.
    6. Select “Configure the Local SpeedStream Gateway Wireless Network”.
    7. The SSID is on this page labeled SSID.


    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    Known Issues

    No known issues at this time.





    Device Manual



    Under Construction.
     
    XB1R Athena, Sep 12, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Siemens: Overview