Netgear: Restore Factory Defaults

Discus and support Netgear: Restore Factory Defaults in XboX Networking Hardware to solve the problem; Netgear (Routers): Restore Factory Defaults Netgear WNR834M Login Information Gateway - 192.168.1.1, 10.0.0.1, or http://routerlogin.net Username -... Discussion in 'XboX Networking Hardware' started by XB1R Hades, May 14, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Netgear: Restore Factory Defaults


    Netgear (Routers): Restore Factory Defaults
    Netgear WNR834M

    Login Information


    Netgear Smart Wizard - Light Blue

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.


    :)
     
    XB1R Hades, May 14, 2014
    #1
  2. XB1R Athena
    XB1R Athena Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.1.1, 10.0.0.1, or routerlogin.net
    • Username – admin
    • Password – password

    Netgear - Smart Wizard- Light Blue



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
    Netgear - Genie - Black/Purple



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Athena, May 14, 2014
    #2
  3. XB1R Apollo
    XB1R Apollo Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.0.1 (v1-v5) or 192.168.1.1 (v6-v10)
    • Username - admin
    • Password - password

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Apollo, May 14, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Netgear: Restore Factory Defaults