Netgear: Restore Factory Defaults

Discus and support Netgear: Restore Factory Defaults in XboX Networking Hardware to solve the problem; Netgear (Routers): Restore Factory Defaults Netgear KWGR614 Login Information Gateway - 192.168.1.1, 10.0.0.1, or http://routerlogin.net Username -... Discussion in 'XboX Networking Hardware' started by XB1R Hades, May 2, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Netgear: Restore Factory Defaults


    Netgear (Routers): Restore Factory Defaults
    Netgear KWGR614

    Login Information

    Netgear Smart Wizard *

    *This router is “open source” meaning custom versions of firmware can be created for its use. This walkthrough is only intended to be used on the default stock version of the firmware.

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.


    :)
     
    XB1R Hades, May 2, 2014
    #1
  2. XB1R Athena
    XB1R Athena Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.1.1, 10.0.0.1, or routerlogin.net
    • Username – admin
    • Password – password

    Netgear - Smart Wizard- Light Blue



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
    Netgear - Genie - Black/Purple



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Athena, May 2, 2014
    #2
  3. XB1R Apollo
    XB1R Apollo Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.0.1 (v1-v5) or 192.168.1.1 (v6-v10)
    • Username - admin
    • Password - password

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Apollo, May 2, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Netgear: Restore Factory Defaults