Netgear Netgear DGND3700: Restore Factory Defaults

Discus and support Netgear Netgear DGND3700: Restore Factory Defaults in XboX Networking Hardware to solve the problem; Netgear (Modems/Gateways) Netgear DGND3700: Restore Factory Defaults Netgear DGND3700 Login Information: Default Gateway - 192.168.0.1 Username –... Discussion in 'XboX Networking Hardware' started by XBR Poseidon, May 18, 2014.

  1. XBR Poseidon
    XBR Poseidon Guest

    Netgear Netgear DGND3700: Restore Factory Defaults


    Netgear (Modems/Gateways) Netgear DGND3700: Restore Factory Defaults
    Netgear DGND3700

    Login Information:

    • Default Gateway - 192.168.0.1
    • Username – admin
    • Password – password



    Restore Factory Defaults



    Through firmware



    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to the router by entering 192.168.0.1 in to the address bar.
    3. Enter the username “admin” and the password “password”.
    4. Select Backup Settings from under the Maintenance section.
    5. Click the Erase button at the bottom of the screen.
    6. Confirm the action if needed.


    Through Hardware



    1. Plug the computer into a LAN port via an ethernet cable.
    2. Press and hold both the Wireless On/Off and WPS buttons for six seconds.

    :)
     
    XBR Poseidon, May 18, 2014
    #1
  2. XBR Poseidon
    XBR Poseidon Guest
    Netgear Netgear DGND3700: Device Manual

    Netgear (Modems/Gateways) Netgear DGND3700: Device Manual
    Netgear DGND3700

    Login Information:

    • Default Gateway - 192.168.0.1
    • Username – admin
    • Password – password



    Device Manual

    Support Page.
     
    XBR Poseidon, May 18, 2014
    #2
  3. XB1R Athena
    XB1R Athena Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.1.1, 10.0.0.1, or routerlogin.net
    • Username – admin
    • Password – password

    Netgear - Smart Wizard- Light Blue



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
    Netgear - Genie - Black/Purple



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Athena, May 18, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Netgear Netgear DGND3700: Restore Factory Defaults