Netgear Netgear DGN2200: Restore Factory Defaults

Discus and support Netgear Netgear DGN2200: Restore Factory Defaults in XboX Networking Hardware to solve the problem; Netgear (Modems/Gateways) Netgear DGN2200: Restore Factory Defaults Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin... Discussion in 'XboX Networking Hardware' started by XB1R Hades, Jul 16, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Netgear Netgear DGN2200: Restore Factory Defaults


    Netgear (Modems/Gateways) Netgear DGN2200: Restore Factory Defaults
    Netgear DGN2200

    Login Information

    • Gateway - 192.168.0.1
    • Username - admin
    • Password - password
    Netgear SmartWizard

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.


    Netgear Genie

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.


    :)
     
    XB1R Hades, Jul 16, 2014
    #1
  2. XB1R Athena
    XB1R Athena Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.1.1, 10.0.0.1, or routerlogin.net
    • Username – admin
    • Password – password

    Netgear - Smart Wizard- Light Blue



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
    Netgear - Genie - Black/Purple



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Athena, Jul 16, 2014
    #2
  3. XB1R Apollo
    XB1R Apollo Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.0.1 (v1-v5) or 192.168.1.1 (v6-v10)
    • Username - admin
    • Password - password

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Apollo, Jul 16, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Netgear Netgear DGN2200: Restore Factory Defaults