Netgear Netgear DGN2200: Overview

Discus and support Netgear Netgear DGN2200: Overview in XboX Networking Hardware to solve the problem; Netgear (Modems/Gateways) Netgear DGN2200: Overview Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password... Discussion in 'XboX Networking Hardware' started by XB1R Hades, Jul 16, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Netgear Netgear DGN2200: Overview


    Netgear (Modems/Gateways) Netgear DGN2200: Overview
    Netgear DGN2200

    Login Information

    • Gateway - 192.168.0.1
    • Username - admin
    • Password - password

    Netgear SmartWizard

    How to Find SSID (Network Name)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The Network name will be listed as Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. Under Security Options select Disable.
    5. Select Apply.


    MAC Filtering

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. Under advanced select Wireless Settings.
    6. Select Setup Access List To access MAC Filtering.
    7. Uncheck Turn Access Control On
    8. Select Apply.


    Change Wireless Channel

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).
    7. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. Select from the mode drop down "Up to 54Mbps".
    7. Click Apply.




    DHCP Reservation

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin"/password.
    3. Click LAN Setup on the left.
    4. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    5. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then
      click "Add" to finished the process.


    UPnP

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section choose UPnP.
    4. Toggle UPnP.


    DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Check the box next to Default DMZ Server.
    5. Enter the IP address assigned to the Xbox console you wish to DMZ.


    Disable DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Uncheck the box next to Default DMZ Server.
    5. Select apply.


    Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Click the Add Custom Service button at the bottom.
    6. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish
      to port forward has.
    7. Click Apply.


    Disable Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Select the radio button for any rules needed to be removed.
    6. Select Delete Service.
    7. Select apply.


    Firewall

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left select WAN Setup.
    4. Check the Disable SPI Firewall box.
    5. Change NAT Filtering from secured to Open.


    How to Find Firmware Version



    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    4. From the left hand menu select Router Status.
    5. The firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administration from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router
      finishes restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.




    Entering PPPoE

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    4. From the left hand menu select Basic Settings.
    5. Where it says Does your internet connection require a login select yes.
    6. Enter the user name and password for your pppoe in their respective fields.
    7. Select apply.




    Known Issues

    There are no known issues with this device.

    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    Netgear Genie

    How to Find SSID (Network Name)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select Basic from the menu on the top.
    4. Select Wireless from the left menu.
    5. Your network name will be listed as Name(SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. Under Security Options select the desired security type.
    6. Select Apply.


    MAC Filtering

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select Advanced from the menu on the left.
    4. Under Advanced select Wireless Settings.
    5. Select Setup Access List to access MAC Filtering.
    6. Uncheck Turn Access Control On
    7. Select Apply.


    Change Wireless Channel

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open a web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select Wireless settings from the left hand menu under Setup.
    8. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11)
    9. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select from the mode drop down "Up to 54Mbps".
    8. Click Apply.
    Change Wireless Band (Width)



    The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set
    the wireless band to 20MHz only, follow these steps.



    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering Router login in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select from the mode drop down "Up to 217Mbps" or lower.
    8. Select Apply.


    DHCP Reservation

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin"/password.
    3. Select Advanced from the tabs at the top.
    4. Click Setup from the menu on the left.
    5. Click Lan Setup in the submenu that appears.
    6. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    7. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then
      click "Add" to finish the process.
    UPnP

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu choose UPnP.
    6. Toggle UPnP.


    DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Check the box next to Default DMZ Server if it is not.
    7. Enter the IP address assigned to the Xbox console you wish to DMZ
    8. Select Apply.



    Disable DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Uncheck the Default DMZ Server
    7. Select Apply.


    Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Click the Add Custom Service button at the bottom.
    8. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish
      to port forward has.
    9. Click apply.
    Disable Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Select the service you want to delete from the radio button on the left.
    8. Select Delete Service.

    Firewall

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Setup setup from the menu on the left.
    5. From the submenu select WAN Setup.
    6. Check the Disable SPI Firewall box.
    7. Change NAT Filtering from secured to Open.


    How to Find Firmware Version

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Administration from the menu on the left.
    5. Select Router Status under administration.
    6. The Firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select administration from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router
      finishes restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed.


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.



    Entering PPPoE

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select the Basic tab from the tabs at the top.
    4. Select Internet from the menu on the left
    5. Where it asks if your internet connection requires a login select yes.
    6. Input in your PPPOE user name and password.
    7. Select Apply.


    :)
     
    XB1R Hades, Jul 16, 2014
    #1
  2. XB1R Hades
    XB1R Hades Guest
    Netgear Netgear DGN2200: Known Issues

    Netgear (Modems/Gateways) Netgear DGN2200: Known Issues
    Netgear DGN2200

    Login Information

    • Gateway - 192.168.0.1
    • Username - admin
    • Password - password


    Known Issues

    There are no known issues with this device.

     
    XB1R Hades, Jul 16, 2014
    #2
  3. XB1R Athena
    XB1R Athena Guest
    Netgear Netgear DGN2200: Device Manual

    Netgear (Modems/Gateways) Netgear DGN2200: Device Manual
    Device Manual

    Click
    here     to go to a manual for this device
     
    XB1R Athena, Jul 16, 2014
    #3
  4. MORPHOLE Win User

    Netgear Netgear DGN2200: UPnP

    Having a number of multiple xbox one NAT issues (particularly with Destiny) with this gateway.
  5. DannyTx Win User

    Netgear: Overview

    I can't seem to get my nat type to open even after all these steps and the steps xbox provides for "cant find teredo IP" when i run multiplayer test I get that, and when i check more details it says im behind a firewall or not connected. I made sure i disabled
    SIP ALG and changed nat to open, and still doesnt work.
  6. GMAN990 Win User

    Moderate nat

  7. Geth Win User

    Netgear Netgear DGN2200: Xbox one can not connect to wifi network

  8. XBF Leonzo G Win User

    Netgear Netgear R7000: Wifi Netgear

    Hi Blah Blah Blah!

    Thank you very much for bringing this issue to our attention. Are you trying to connect an Xbox One or Xbox 360 to your WiFi? The answers stated above are all great troubleshooting steps to try in order to resolve this issue. We also recommend using this
    article
    Xbox One Network Connection Error Solution    . These solutions are for the Xbox One. If you need the solutions for the Xbox 360, please let us know. Be sure to let us know the results!
Thema:

Netgear Netgear DGN2200: Overview

Loading...

  1. Netgear Netgear DGN2200: Overview - Similar Threads - Netgear Netgear DGN2200

  2. Netgear Netgear DGN2200: Xbox one can not connect to wifi network

    in XboX Networking Hardware
    Netgear Netgear DGN2200: Xbox one can not connect to wifi network: Netgear (Modems/Gateways) Netgear DGN2200: Xbox one can not connect to wifi network This may help with your issue. Xbox One Network Connection Help | Troubleshoot Xbox Live Connection...

  3. Netgear Netgear DGN2200: My internet speed is slow. Is there a DNS around Greensburg Indiana ...

    in XboX Networking Hardware
    Netgear Netgear DGN2200: My internet speed is slow. Is there a DNS around Greensburg Indiana ...: Netgear (Modems/Gateways) Netgear DGN2200: My internet speed is slow. Is there a DNS around Greensburg Indiana that could help my internet? I live in Greensburg Indiana, my internet connection is...

  4. Netgear Netgear DGN2200: Known Issues

    in XboX Networking Hardware
    Netgear Netgear DGN2200: Known Issues: Netgear (Modems/Gateways) Netgear DGN2200: Known Issues Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Known Issues There are no known...

  5. Netgear Netgear DGN2200: Entering PPPoE

    in XboX Networking Hardware
    Netgear Netgear DGN2200: Entering PPPoE: Netgear (Modems/Gateways) Netgear DGN2200: Entering PPPoE Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Netgear SmartWizard Entering PPPoE...

  6. Netgear Netgear DGN2200: Restore Factory Defaults

    in XboX Networking Hardware
    Netgear Netgear DGN2200: Restore Factory Defaults: Netgear (Modems/Gateways) Netgear DGN2200: Restore Factory Defaults Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Netgear SmartWizard Restore...

  7. Netgear Netgear DGN2200: Firmware Update

    in XboX Networking Hardware
    Netgear Netgear DGN2200: Firmware Update: Netgear (Modems/Gateways) Netgear DGN2200: Firmware Update Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Netgear SmartWizard Firmware Update...

  8. Netgear Netgear DGN2200: How to Find Firmware Version

    in XboX Networking Hardware
    Netgear Netgear DGN2200: How to Find Firmware Version: Netgear (Modems/Gateways) Netgear DGN2200: How to Find Firmware Version Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Netgear SmartWizard How...

  9. Netgear Netgear DGN2200: Firewall

    in XboX Networking Hardware
    Netgear Netgear DGN2200: Firewall: Netgear (Modems/Gateways) Netgear DGN2200: Firewall Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Netgear SmartWizard Firewall Login to...

  10. Netgear Netgear DGN2200: DMZ

    in XboX Networking Hardware
    Netgear Netgear DGN2200: DMZ: Netgear (Modems/Gateways) Netgear DGN2200: DMZ Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Netgear SmartWizard DMZ Login to router by...