Netgear Netgear CG3100D: Restore Factory Defaults

Discus and support Netgear Netgear CG3100D: Restore Factory Defaults in XboX Networking Hardware to solve the problem; Netgear (Modems/Gateways) Netgear CG3100D: Restore Factory Defaults Netgear CG3100D Login Information: Default Gateway - 192.168.0.1 Username –... Discussion in 'XboX Networking Hardware' started by XBR Poseidon, May 19, 2014.

  1. XBR Poseidon
    XBR Poseidon Guest

    Netgear Netgear CG3100D: Restore Factory Defaults


    Netgear (Modems/Gateways) Netgear CG3100D: Restore Factory Defaults
    Netgear CG3100D

    Login Information:

    • Default Gateway - 192.168.0.1
    • Username – admin
    • Password – password



    Restore Factory Defaults

    Through firmware

    *Not Available*

    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the bottom of the gateway.
    3. Press and hold the reset button for 7 seconds.


    :)
     
    XBR Poseidon, May 19, 2014
    #1
  2. XB1R Athena
    XB1R Athena Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.1.1, 10.0.0.1, or routerlogin.net
    • Username – admin
    • Password – password

    Netgear - Smart Wizard- Light Blue



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
    Netgear - Genie - Black/Purple



    Restoring Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Athena, May 19, 2014
    #2
  3. XB1R Apollo
    XB1R Apollo Guest
    Netgear: Restore Factory Defaults

    Netgear (Routers): Restore Factory Defaults
    Login Information

    • Gateway - 192.168.0.1 (v1-v5) or 192.168.1.1 (v6-v10)
    • Username - admin
    • Password - password

    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.
     
    XB1R Apollo, May 19, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Netgear Netgear CG3100D: Restore Factory Defaults