Netgear: Firmware Update

Discus and support Netgear: Firmware Update in XboX Networking Hardware to solve the problem; Netgear (Routers): Firmware Update Netgear MR814 Login Information Gateway - 192.168.1.1, 10.0.0.1, or http://routerlogin.net Username - admin... Discussion in 'XboX Networking Hardware' started by XB1R Hades, May 9, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Netgear: Firmware Update


    Netgear (Routers): Firmware Update
    Netgear MR814

    Login Information

    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    5. The Netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administraion from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, un-compress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
      restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed

    :)
     
    XB1R Hades, May 9, 2014
    #1
  2. XB1R Apollo
    XB1R Apollo Guest
    Netgear: Firmware Update

    Netgear (Routers): Firmware Update
    Login Information


    How to Find Firmware Version

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Router Status.
    5. The firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administraion from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
      restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed
     
    XB1R Apollo, May 9, 2014
    #2
  3. XB1R Apollo
    XB1R Apollo Guest
    Netgear: Firmware Update

    Netgear (Routers): Firmware Update
    Login Information

    How to Find Firmware Version

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Router Status.
    5. The firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net       in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administraion from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
      restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed
    .
     
    XB1R Apollo, May 9, 2014
    #3
    Error:Failed to connect to localhost port 9200: Connection refused
Thema:

Netgear: Firmware Update