Draytek: Overview

Draytek (Modems/Gateways): Overview
Draytek- Vigor2500

Login Information:

Default Gateway – 192.168.1.1

Username – *none*

Password – *none*



How to Find SSID (Network Name)

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select Wireless LAN Information from under Basic Setup.
5. Select General Settings from under Detailed Settings.
6. Your network name can be found in the SSID field.

How To Find Wireless Passphrase (WPA/WEP)

*NOTE, The wireless passphrase cannot be viewed, only reset.*

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the OK button.
4. Select Wireless LAN Information from under Basic Setup.
5. Select WEP Settings from under Detailed Settings.
6. Enter your desired key in key 1. It must be 10 digits long and can only use 0-9 and a-f.
   
7. Click the OK button once the desired key has been entered.

Changing Wireless Security Type/ Disabling Wireless Security

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the OK button.
4. Select Wireless LAN Information from under Basic Setup.
5. Select WEP Settings from under Detailed Settings.
6. Select Disable in the WEP Encryption drop down.
7. Click the OK button.

MAC Filtering

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the OK button.
4. Select Wireless LAN Information from under Basic Setup.
5. Select Access Control from under Detailed Settings.
6. Uncheck the Enable Access Control check box.
7. Click the OK button.

Change Wireless Mode

*This device supports the 802.11b standard only.*





Change Wireless Channel

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select General Settings under Detailed Settings.
5. Select the Desired channel from the channel drop down. (Channels 1,3,9,11)
6. Click the OK button.

DHCP Reservation

*Not Available*



UPnP

I could find no reference of UPnP in the device manual. Device Spec indicates UPnP compatability.

DMZ

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select Advanced Setup from the Main Menu.
5. Select NAT Setup.
6. Select DMZ Host Setup.
7. Check the Enable box.
8. Click the Choose PC button and select the Xbox from the resulting window. Or enter the IP Address of your Xbox console.
   
9. Click the OK button.

Disable DMZ

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select Advanced Setup from the Main Menu.
5. Select NAT Setup.
6. Select DMZ Host Setup.
7. Uncheck the Enable box.
8. Click the OK button.

Port Forwarding

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select NAT Setup in the Advanced Setup Section.
5. Select Open Ports Setup.
6. Click on the number of the next available Index.
7. Check the Enable Open Ports box.
8. Enter “Xbox Live” in the comment field.
9. Click the Choose PC button and choose the Xbox from the resulting list.
10. Set Protocol to Both. If both is not available two rules will need to be created one UDP and the other TCP.
    
11. Set both the Start Port and End Port to 3074.
12. Click the OK button.

Disable Port Forwarding

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select NAT Setup in the Advanced Setup Section.
5. Select Open Ports Setup.
6. Click the Index number next to the rule that was created.
7. Click the Clear All button.
8. Click the OK button.

Firewall

*The firewall does not have any adjustable options.*



Restoring Factory Defaults

Through Firmware

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select System Management from the Main Menu.
5. Select Reboot System.
6. Select Using factory default configuration.
7. Click the OK button.

Through Hardware

1. Locate the reset button on the back of the device.
2. Press and hold the reset button for aprox. 5 seconds.
3. Release the button and wait for the device to restart.

How to Find Firmware Version

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. The firmware version is listed at the top of the screen to the right of Firmware.
   

Firmware Update

1. Obtain the updated firmware file either from your ISP or Draytek.
2. Open a web browser.
3. Enter http://192.168.1.1 (or click the link).
   
4. Click the Ok button.
5. Select System Management from the main menu.
6. Select Firmware Upgrade.
7. Follow the onscreen instructions to complete this action using an FTP Client.
   

Bridging Guide

1. Open a web browser.
2. Enter http://192.168.1.1 (or click the link).
   
3. Click the Ok button.
4. Select Quick Setup.
5. Select Internet Access Setup.
6. Select PPPoE/PPPoA.
7. Set PPPoE/PPPoA Client to Disable.
8. Select 1483 Bridged IP LLC in the Encapsulation drop down.
9. Click the OK button.

Multiple Console Support

We have confirmed that this network device is unable to support more than one console with an Open NAT.



Known Issues

There are no known issues at this time.

Device Manual

Click
here for the manual.

:)

 

Draytek: DHCP Reservation

Draytek (Modems/Gateways): DHCP Reservation
Draytek- Vigor2500

Login Information:

Default Gateway – 192.168.1.1

Username – *none*

Password – *none*



DHCP Reservation

*Not Available*

 

Draytek: Known Issues

Draytek (Modems/Gateways): Known Issues
Draytek- Vigor2500

Login Information:

Default Gateway – 192.168.1.1

Username – *none*

Password – *none*



Known Issues

There are no known issues at this time.