By navigating in the menu from right to left (even with LB and RB) no sound is transmitted...

There are no left or right buttons on the controller, bit of a pain to navigate the menus when you're asked to press LB or RB. The only fix it to turn the wheel off and use a controller to do the LB/RB and then switch back to the wheel. I don't see where
they could have put the buttons to be honest but it is a little annoying not having them.

hi, @ltu93

just go over to your storage or system info and type in one of these codes

LT, RT, X, Y, LB, RB, LEFT, Y, RIGHT, RIGHT​

OR​

LT, RT, X, Y, LB, RB, UP, LB, LB, X​

OR​

LT, RT, X, Y, LB, RB, Y, UP, LEFT, UP​

OR​

LT, RT, X, Y, LB, RB, Y, RIGHT, DOWN, RIGHT​

OR​

LT, RT, X, Y, LB, RB, RIGHT, LEFT, RIGHT​

OR​

LT, RT, X, Y, LB, RB, Y, DOWN, LEFT, DOWN​

OR​

LT, RT, X, Y, LB, RB, B, Y, A, X​

OR​

LT, RT, X, Y, LB, RB, Y, RIGHT, LEFT, DOWN​

OR​

LT, RT, X, Y, LB, RB, Y, LEFT, UP, LEFT​

OR​

LT, RT, X, Y, LB, RB, LT, RT, X, Y, LEFT, UP​

OR​

LT, RT, X, Y, LB, RB, Y, LEFT, UP, LEFT​

Hope this may solved your issue:

Was my post helpful? Please give it a Like.

Settings -> System -> System Info, now type each one of these codes then a prompt will come up asking to rest the xbox to default, if none of them work, you'll need to call Xbox Support at 1800-4MY-Xbox.:

LT, RT, X, Y, LB, RB, LEFT, Y, RIGHT, RIGHT

OR

LT, RT, X, Y, LB, RB, UP, LB, LB, X

OR

LT, RT, X, Y, LB, RB, Y, UP, LEFT, UP

OR

LT, RT, X, Y, LB, RB, Y, RIGHT, DOWN, RIGHT

OR

LT, RT, X, Y, LB, RB, RIGHT, LEFT, RIGHT

OR

LT, RT, X, Y, LB, RB, Y, DOWN, LEFT, DOWN

OR

LT, RT, X, Y, LB, RB, B, Y, A, X

OR

LT, RT, X, Y, LB, RB, Y, RIGHT, LEFT, DOWN

OR

LT, RT, X, Y, LB, RB, Y, LEFT, UP, LEFT

OR

LT, RT, X, Y, LB, RB, LT, RT, X, Y, LEFT, UP

OR

LT, RT, X, Y, LB, RB, Y, LEFT, UP, LEFT

When you are on the menu, use the bumpers (RB and LB) to navigate your way to the campaign.

Hello,

Before you begin, disconnect your devices (HDD, memory card).

Go to settings, console settings, System Info.

Finally made one code that follows (depending on the model of the console this may vary):

-LT, RT, X, Y, LB, RB, X, Y, Y, X

-LT, RT, X, Y, LB, RB, X, Y, X, Y

-LT, RT, X, Y, LB, RB, X, Y, right, left

-LT, RT, X, Y, LB, RB, X, Y, left, right

-LT, RT, X, Y, LB, RB, X, Y, up, down

-LT. RT. X. Y. LB. RB. down. down. down. down.

So a message appears offering to reset console settings, you just have to accept.